innokin

 iTaste MVP v2.0 – Vape Vitals
Manufacturer Innokin
Tank Style Cartomizer
Method Direct Draw
Threading 510/eGo
Battery Style Li-Ion 2600mAh
Warranty 90 Days
Replacement Tanks Soon
MSRP 69.99
 
 

itaste-mvp-vape-world-kb-main-image

Brief Overview

The iTaste MVP v2.0 is a substantial upgrade of the original iTaste MVP the iTaste MVP V2.0 has substantial improvements in both appearance and function. USB Power output, passthrough, huge battery, Innokin thought of everything!

See User Guides below for full usage information.

Using Your MVP v2.0

A:The MVP offers a lot of great features. From Variable Voltage and Wattage, to the 510 threading, iClear 30b cartomizer and USB power-out, you’re ready to go out of the box, and upgrading in the future is a snap! Please refer to the full instructions located on the ‘User Guide’ tab, but here is a quick rundown on using the MVP v2.0:

Charge the MVP v2.0 – with the included charger, it could take a few hours the first time as the 2600mAh battery is a bit large, but subsequent charges should not take longer than an hour or so.

Load the MVP v2.0 – Loading the tank is easily done by removing the drip tip mouthpiece, and fill the iClear 30B tank with a liquid of your choice. Stop filling long before the top mark or the liquid overflows into the center tube. After you replace the mouthpiece, make sure the wick is fully saturated by standing it vertically and allowing it to stand for two minutes. Avoid ‘dry firing’ by pressing the power button for one second, which should create just enough heat to allow the liquid to fully saturate the wicks; then use as normal.

Power up and draw – There is a three click safety switch on the MVP v2.0, press the button three times to unlock, the LED should flash when you do so. (reverse process to lock.)

The iTaste MVP v2.0 can automatically read any 510 atomizer you attach and adjust its power output accordingly, so if you don’t want to even know anything about variable voltage(VV), and variable wattage(VW)then just press the button and draw! If you want to add a new cartomizer in the future, as long as it has 510 threading, you are good to go!

Use until you have had your fill, or the ten-second shut off turns the atomizer off.

A: The MVP v2.0 heats up instantly. With a powerful 2600mAh Li-Ion battery, the MVP v2.0 heats up fast.
A: This is complicated to answer. There aren’t any direct temperature settings, but by varying the wattage and voltage combination, you can get the atomizer to change temperatures, which will create different vapor qualities. This process takes much practice and experimentation, and you will probably blow out an atomizer coil or two, but the upside is that you will eventually have full control over your vapors, and as you try different liquids(Each seems to have a unique vapor identity) and you can adjust the MVP to create exactly what you want, no matter what you load.

See the VV / VW tab on the left for more information.

A: First and foremost its vital that you use the cleanest and purest liquids you can find. The MVP v2.0 was designed for use with liquids that vaporize cleanly and leave no particulate behind.

Again, this is complicated to answer. There aren’t any direct temperature settings, but by varying the wattage and voltage combination, you can get the atomizer to change temperatures, which will create different vapor qualities. This process takes much practice and experimentation, and you will probably blow out an atomizer coil or two, but the upside is that you will eventually have full control over your vapors, and as you try different liquids (Each seems to have a unique vapor identity) and you can adjust the MVP to create exactly what you want, no matter what you load.

See the VV / VW tab on the left for more information.

A: The MVP v2.0 was designed solely for liquids.

Do not put aromatic blends or solid concentrates that melt into the atomizer included with the the MVP v2.0. Other cartomizers and tanks that are designed for 510 threading.

A: The charger is rated from 100v to 240v, but you may need an outlet adapter for locations outside of North America.
A: First and foremost its vital that you use the cleanest and purest liquids you can find. The MVP v2.0 was designed for use with liquids that vaporize cleanly and leave no particulate behind.

Atomizers will last for 4-5 weeks, and should be replaced as needed. Your experience will vary.

This is complicated to answer. There aren’t any direct temperature settings, but by varying the wattage and voltage combination, you can get the atomizer to change temperatures, which will create different vapor qualities. This process takes much practice and experimentation, and you will probably blow out an atomizer coil or two, but the upside is that you will eventually have full control over your vapors, and as you try different liquids(Each seems to have a unique vapor identity) and you can adjust the MVP to create exactly what you want, no matter what you load.

See the VV / VW tab on the left for more information.

A: The atomizer coil is nickel/aluminum-alloy, the wick is fiberglass, the tank on the iClear 30b is plastic, the body is made of steel and aluminum.
A: The MVP v2.0 has a nickel/aluminum-alloy atomizer coil that surrounds a fiberglass wick.
A: Liquids love high temperatures, so you should not have an overheating issue!
A: Is best to not fill the tank past the level of the center tube. 2/3 full should be just fine. The MVP v2.0 was designed to hold 1.6ml.
A: Yes, after ten seconds of use, the MVP v2.0 will power off.

As a general safety rule, do not leave the MVP v2.0 unattended while powered on.

A: The MVP v2.0 atomizers are replaceable, and also rebuildable. You can replace them very easily by disconnecting the tank from the battery, and replace with any 510 threaded fresh tank.
A: The battery is an Li-Ion 2600mAh barrel battery. The housing has 510, and eGo threads.
A: The MVP v2.0 comes with an AC adapter with full USB charging capability.
A: When the MVP v2.0 Battery is in need of a charge, the power button will flash RED, and vapor production will stop.

At this time, remove the cartomizer and connect it to the AC adapter.

Once the red LED light turns green, the MVP v2.0 Battery has been fully charged.

A: Allow 3-4 hours charging time for the first 3-4 cycles. Then, it should only take about one hour to charge, depending on your charging source.

Cleaning & Maintenance

A: Any liquid that may have spilled out or collected on the body of your MVP v2.0 can be removed with a warm damp cloth.

If you have noticed that even a single drop of moisture exists on the exterior of the MVP v2.0, remove the tank from the Unit and check the threading areas and make sure it is free of moisture & debris.

Within the atomizer of your MVP v2.0 iClear 30b, the coil works to clean itself by burning off any residue that comes in contact with it. We don’t recommend using any type of liquid cleaning agent in the MVP v2.0 tank, as doing so could cause it to malfunction. If you are having issues with the atomizer, namely a distinct change in aroma, please replace it. Atomizers do not last more than 4-5 weeks with normal use. Your experience will vary.

The mouthpiece can be soaked in isopropyl alcohol until the buildup dissolves. Do not clean the rubber or silicone o-rings with alcohol, as it could damage the rubber. Remove o-ring with a non-sharp tool(toothpicks work well) then use warm soap and water to clean.

A: If you are having issues with the atomizer, namely a distinct change in aroma, please replace. Atomizers do not last more than 4-5 weeks with normal use. Your experience will vary.
Monitor and replace atomizer as needed. Check your vape each time you use it, it will tell you how often it needs to be cleaned.
A: Cleaning the atomizer is not recommended. Replace as needed.

Make sure you don’t expose the atomizer or battery to any cleaning liquids whatsoever. If you need to clean the outside of the MVP v2.0, use a warm damp cloth. If the MVP v2.0 gets wet in any way, allow to dry in the sun or a warm dry area until COMPLETELY DRY. Attempting to use the MVP v2.0 if wet will cause serious damage to the unit.

If you have noticed that even a single drop of moisture exists on the exterior of the MVP v2.0, remove the tank from the Unit and check the threading areas and make sure it is free of moisture & debris.

A: The atomizer should be replaced as needed on the MVP v2.0. Over time even the purest liquids will allow buildup to collect on the Atomizer coil; replace as needed.

Atomizers will last 4-5 weeks with normal use. Your experience will vary.

Ordering – Returns – Warranty

A: 90 Days
A: Not at this time.
A:

Innokin MVP v2.0 90 Day Warranty

VapeWorld is handling all of the warranty requests and service for the MVP v2.0.

Innokin warrants our products to be free from defects in materials and workmanship for 90 days from the date of purchase under proper use. Warranty excludes cartridges, misuse or abuse, and any accidental damages.

*IMPORTANT: WARRANTIES NON-TRANSFERABLE. ITEMS PURCHASED ONLINE FROM E-BAY, AMAZON, CRAIGSLIST, ETC. ARE CONSIDERED 2ND HAND AND WARRANTIES NULL AND VOID!

If you need more information about MVP v2.0’s Warranty, please contact us

A: Your warranty period begins with your date of purchase. Contact Vape World for more information about warranty registration. If you need proof of purchase information for your Vape World purchased MVP v2.0, please contact us.

If you have any other questions about the MVP v2.0 vaporizer, please contact us!

Product Dimensions 4.25in x 1.6in x .85in (10.8cm x 4.06cm x 2.15cm)
Package Dimensions 5.5in x 3in x 1.75in (13.8cm x 7.62cm x 4.44cm)
Product Weight .35lbs (.15kg)
Package Weight .7lbs (..38kg)
Vapor Path Steel, Plastic
Tank Material Plastic
Tank Capacity 3ml
Charging Options 110v/240v/USB
Battery Capacity 2600mAh
Auto-Off? Yes, 10 second
Safety Power Switch 3 Click
Heating Element Nickel/Aluminum-Alloy coil
Warm-Up Time ~1 Seconds
Country of Manufacture China
Warranty 90 Day

Included with Purchase:

  • MVP v2.0 Mod Unit
  • 18650 2000 mAh Li-Ion Battery
  • iClear 30b Cartridge
  • AC Charger
  • User Manual

MVP v2.0 User Guides

  • Coming Soon
*Adobe Reader or PDF viewer Required

Getting the Most Out of Your MVP v2.0

  • Never leave a MVP v2.0 in a hot car. Ever.
  • Allowing the MVP v2.0 to freeze can damage the atomizer. Avoid temperatures below 40 degrees.
  • Overloading more than 3ml will cause liquid to enter the center tube, avoid this at all costs. If this occurs, remove tank from MVP v2.0 Body, empty of liquid, remove atomizer and clear center tube of liquid before putting everything back together.

MVP v2.0 Maintenance

Cleaning the MVP v2.0 couldn’t be easier. Use the atomizer until the aroma suddenly changes, then replace or rebuild.

Atomizers will last 4-5 weeks with normal use; your experience will vary.

The inside of the mouthpiece will take on the most buildup, soak it in warm soapy water, or isopropyl alcohol and clean with a cotton swab if needed. Dry completely before re-using.

If any liquid has made it onto the body of the MVP v2.0, wipe off with a warm damp cloth.

Need Assistance with your MVP v2.0?

Try these Solutions to common issues:

A: Check that the batteries are fully charged, and that all connections are solid and tight. If you have fully charged batteries, and no light on the button when you press it, then something is wrong with the MVP v2.0 Unit.

If you are getting a light around the button, but no vapor production, remove the atomizer and check for moisture or debris at the connection. If its good to go, replace the atomizer and see if you have vapor production. The only three things that can be faulty are the battery, the switch, or the atomizer. It should be easy to isolate the issue.

A: Make sure your MVP v2.0 is fully charged, and the atomizer coil is fully seated and loaded properly(not overloaded).

If you are getting a light around the button, but no vapor production, remove the atomizer and check for moisture or debris at the connection. If its good to go, replace the atomizer and see if you have vapor production. The only three things that can be faulty are the battery, the switch, or the atomizer. It should be easy to isolate the issue.

A: The atomizers will last 4-5 weeks with normal use, although your experience will vary. Replace your atomizer when you feel it needs it. A change in aroma will be your first indicator the atomizer has died.

If these troubleshooting tips don’t work, please contact us.

Innokin 90 Day Limited Warranty

Innokin is handling all of the warranty requests and service for the MVP 2.0.

To be eligible for service under this warranty you MUST return the warranty registration card, the dated receipt or purchase order, or other proof of purchase indicating the date purchased, within three months 90 days of purchasing your genuine Innokin product. Send these items to:

How Do You Get Service? To be eligible for service under this warranty you MUST return the warranty registration card, the dated receipt or purchase order, or other proof of purchase indicating the date purchased, within three months 90 days of purchasing your genuine Innokin product. Send these items to:

After Sales Service Center (California)
17128 Colima Rd #380 Hacienda Heights‎ CA‎ 91745 United States
E-mail: Customerservice@innokin.com

After Sales Service Center ( North Carolina )
8006 Market St Wilmington, NC 28411
Phone : 910-821-0060
Phone : 1-888-681-9235
E-Mail : Innokinreturns@ElectraVapor.com

We will inspect your device to verify that it is a genuine Innokin product, and if so, repair or replace it if it is received within 90 days of the date of purchase.

*IMPORTANT: WARRANTIES NON-TRANSFERABLE. ITEMS PURCHASED ONLINE FROM E-BAY, AMAZON, CRAIGSLIST, ETC. ARE CONSIDERED 2ND HAND AND WARRANTIES NULL AND VOID!

Any other questions? Let us know.
If you need more information about Innokins’s Warranty, please contact us

Tagged:

Leave a Reply