|Innokin Disrupter – Vape Vitals|
|Tank Style||Tank not included|
|Method||N/A (Mod Only)|
|Battery Style||Li-Ion 2000mAh|
|Replacement Parts||Coming Soon|
|MSRP||$39.95(Control Unit) $20.00 (Battery|
The Innokin Disrupter
A radical departure for a mod battery. The design was given a complete overhaul. The control unit is seperate from the battery, so you can swap out batteries as needed. The unit comes in three colors, and the battery comes in 5 colors. The build quality of the attachment is superior to anything on the market. The Disrupter has beautiful brushed anodized aluminum exterior, stronger and increased battery life, short circuit/atomizer protection and sub-ohm options. Variable voltage and variable wattage are standard features on this 50W powerhouse.
Using Your Disrupter
Charge the Disrupter – The detachable 2000mAh battery is quite large so this could take a few hours the first time over USB, but subsequent charges should not take longer than 60-90 minutes.
The Disrupter battery has a tri-color LED on top of the USB port that indicates battery life remaining:
Green = Almost fully Charged. When the Innokin Disrupter is fully recharged the top LED light will power off
Yellow = Half Power
Red = Low Power Charge the Disrupter.
Attach Atomizer The Disrupter does not include an atomizer tank; you must provide your own. VapeWorld Carries SubTanks from KangerTech that work perfectly with the Disrupter. The Disrupter accepts tanks with 510 threading and also includes an eGo-style adapter.
Power up and draw – Make sure the battery is fully attached. Press the power button three times to unlock. There are two buttons that allow you to alter voltagea and wattage. Set to your desired setting for your material and when correct, push the main button to activate the atomizer.
To enter variable voltage(VV) mode, press and hold the Press and hold the “-” button along with the power button for one second to enter variable voltage mode. While in VV mode, press the + or – buttons once and then press again increase or decrease the wattage. Disrupter can be adjusted from 3.0 to 9.0 watts in .1 volt increments. Press the power button to lock the setting.
The Innokin Disrupter features automatic real-time atomizer Ohms detection. If the resistance of the atomizer is lower than 0.4 the Ohms bar will blink and the Disrupter will not power on.
There is also a safety on the power switch, clicking it three times turns off the power button, and repeating this turns the button back on. This is great if you have the Disrupter in your purse, or pocket, as it prevents it from going off accidentally and wasting your battery or worse.
As a general safety rule, do not leave the Disrupter unattended while powered on.
At this time, remove the atomizer and connect the Disrupter Battery to the Disrupter wired USB charger (at the base of the Disrupter).
Cleaning & Maintenance
The draw stem can be cleaned with the brush, or soaked in isopropyl alcohol until the buildup dissolves.
If you need to clean the outside of the Disrupter, use a warm barely damp cloth. If the Disrupter gets wet in any way, allow to dry in the sun or a warm dry area until COMPLETELY DRY. Attempting to use the Disrupter if wet will cause serious damage to the unit.
Ordering – Returns – Warranty
If you have any other questions about the Disrupter vaporizer, please contact us!
|Vapor Path||N / A|
|Chamber Material||N / A|
|Battery Capacity||2000 mAh Li-Ion||Voltage||3.0v to 7.5v|
|Auto-Off?||Yes, 15 Seconds|
|Safety Power Switch||Yes, 3-Click|
|Heating Element||N / A|
|Warm-Up Time||~1 Second|
|Country of Manufacture||China|
Included with Purchase:
- Innokin Disrupter 50W
- USB Charger Cable
- Ego Adapter
- User Manual
Disrupter User Guides
- Coming Soon
*Adobe Reader or PDF viewer Required
Getting the Most Out of Your Disrupter
- Never leave a Disrupter in a hot or frozen car, this will deplete the battery life exponentially.
- Allowing the Disrupter to freeze can damage the atomizer. Avoid temperatures below 40 degrees.
If any buildup has made it onto the body of the Disrupter, wipe off with a warm damp cloth.
Need Assistance with your Disrupter?
Try these Solutions to common issues:
Are you getting any light at all from the button or the LED on the top? If not, make sure that the Innokin is charged properly.
If you have charged the Disrupter fully, unlocked the power button and are still getting no vapors, feel for any warmth at all, and if you feel nothing, please contact us.
If these troubleshooting tips don’t work, please contact us.
Disrupter Accessories coming soon!
Innokin Disrupter 90 Day Limited Warranty
Innokin is handling all of the warranty requests and service for the Disrupter.
To be eligible for service under this warranty you MUST return the warranty registration card, the dated receipt or purchase order, or other proof of purchase indicating the date purchased, within three months 90 days of purchasing your genuine Innokin product. Send these items to:
How Do You Get Service? To be eligible for service under this warranty you MUST return the warranty registration card, the dated receipt or purchase order, or other proof of purchase indicating the date purchased, within three months 90 days of purchasing your genuine Innokin product. Send these items to:
After Sales Service Center (California)
17128 Colima Rd #380 Hacienda Heights CA 91745 United States
After Sales Service Center ( North Carolina )
8006 Market St Wilmington, NC 28411
Phone : 910-821-0060
Phone : 1-888-681-9235
E-Mail : Innokinreturns@ElectraVapor.com
We will inspect your device to verify that it is a genuine Innokin product, and if so, repair or replace it if it is received within 90 days of the date of purchase.
*IMPORTANT: WARRANTIES NON-TRANSFERABLE. ITEMS PURCHASED ONLINE FROM E-BAY, AMAZON, CRAIGSLIST, ETC. ARE CONSIDERED 2ND HAND AND WARRANTIES NULL AND VOID!
Any other questions? Let us know.
If you need more information about Disrupter’s Warranty, please contact us