Cloupor Vaporizers

 Cloupor M4 – Vape Vitals
Manufacturer Shenzhen Cloupor Technology.
Tank Style Coil/Globe
Method Direct Draw
Threading 510 & eGo
Battery Style Li-Ion 650mAh
Warranty 1 Year
Replacement Globes Included
MSRP 39.99
 
 

cloupor

Brief Overview

See User Guides below for full usage information.

Using Your Cloupor M4

A: As with most pen vaporizers, the Cloupor M4 is super easy to use. Refer to the full instructions located on the ‘User Guide’ tab, but here is a quick rundown on using the Cloupor M4:

Charge the Cloupor M4 – This could take a 1-2 hours the first time, but subsequent charges should not take longer than 45-60 minutes.

Load the Cloupor M4 – The M4 has two different style atomizers, one for aromatic blends, one for concentrates. Be sure to use the proper atomizer. The concentrate atomizer is wrapped around a wick, the blend atomizer has no wick.

Loading the crucible is easily done by removing the draw stem/globe combo, and either using the included tool to apply your concentrates, or loading your blends by hand in the heating chamber. Do not load too much; more than a sessions worth is definitely too much. Ensure the concentrate the making contact with the atomizer before you replace the draw stem/globe. Make sure not to touch the coil with the tool to avoid potential damage.

Power up and draw – If the switch on the Cloupor M4 is locked, unlock by pressing the button five times. This enables the power switch and the Cloupor M4 is ready to use. Press the button begin drawing from the Cloupor M4 after 3 seconds. Draw until you have had your fill, or the ten-second shut off turns the atomizer off.

A: 3 Seconds.
A: There are no temperature settings on the Cloupor M4. It goes from room temperature to its peak temperature in just 3 seconds.
A: First and foremost its vital that you use the cleanest and purest concentrates you can find. The Cloupor M4 was designed for use concentrates that melt cleanly and leave no particulate behind. When using concentrates, it’s recommended to open the air intake on the rotating ring below the tank.

When using aromatic blends, its vital that you use a blend that has been ground consistently. Also, when using aromatic blends, it’s recommended to open the air intake on the rotating ring below the tank.

Since the Cloupor M4 has only one temperature setting, its essentially foolproof. Press the button, and draw until you have your fill.

A: Yes/No. It depends on the atomizer you are using, look closely at the included atomizers in the kit, and make sure that you are using the atomizer that is wrapped around a wick, as opposed to the atomizers that are not. The Cloupor M4 was designed solely for liquids and concentrates. It ships with a crucible/atomizer for solid concentrates, but other tanks are available.

A: The charger is rated from 100v to 240v, but you might need an adapter for your outlet if outside North America. USB option is always available, negating the need for AC adapters, regardless of your location.
A: First and foremost its vital that you use the cleanest and purest liquids and concentrates you can find. The Cloupor M4 was designed for use with liquids and concentrates that melt cleanly and leave no particulate behind. Keep the air intake ring set to the open position with blends, and closed position with concentrates.

Since the Cloupor M4 has only one temperature setting, its essentially foolproof. Press the button, and draw until you have your fill or until the Cloupor M4 shuts off automatically.

A: The atomizer coil is nickel/aluminum-alloy, the wick is fiberglass, the crucible that surrounds the coil is ceramic, the body is made of steel. The globe is made from glass.
A: Nichrome, a non-magnetic alloy of nickel, chromium, and often iron, usually used as a resistance wire in applications from atomizer coils to toasters and beyond.
A: Liquids and concentrates love high temperatures, so you should not have an overheating issue!
A: It’s best to not fill the heating chamber full. Just apply enough for one session at a time. The Cloupor M4 was not designed to hold more than that.
A: Yes, after ten seconds of use, the Cloupor M4 will power off.

There is also a safety on the power switch, clicking it five times turns off the power button, and repeating this turns the button back on. This is great if you have the Cloupor M4 in your purse, or pocket, as it prevents it from going off accidentally and wasting your battery or worse.

A: You can replace them very easily by disconnecting them from the battery, unscrewing the atomizer from its mount and replace with a fresh atomizer.
A: The screen size is proprietary. The screen in the Cloupor M4 can be unscrewed from the bottom of the draw stem and cleaned with isopropyl alcohol; the kit also comes with an extra replacement screen.
A: The battery is a 650mAh Li-Ion barrel battery. It has 510, and eGo threads.
A: The Cloupor M4 comes with an AC adapter/USB plug, rated from 100v to 220v. The USB plug can be used by itself in a powered USB port anywhere in the world, but if you are charging your Cloupor M4 outside of North America with the included AC adapter an outlet/plug adapter might be needed.
A: When the Cloupor M4 Battery is in need of a charge, the power button will flash to indicate what level the battery is at:

RED: 0-2%
Yellow: 3-50%
Green: 50-100%

At this time, connect the Cloupor M4 Battery to the Cloupor M4 Wired USB Charger (at the base of the Cloupor M4 Battery). The Cloupor M4 Wired USB Charger can be connected to either the Wall Adapter or any compatible USB port. A red LED light will illuminate to indicate that a charge is being administered.

Once the red LED light turns green, the Cloupor M4 Battery has been fully charged.

A: According to Shenzen Cloupor Technology., allow 1-2 hours charging time for the first 3-4 cycles. Then, it should only take about one hour to charge, depending on your charging source. Using the AC USB adapter will charger your M4 faster than most USB ports.

Cleaning & Maintenance

A: Any concentrate that may have collected on the body of your Cloupor M4 can be removed with a warm damp cloth.

If you need to remove essential oil from inside the crucible, it’s not advisable, but you can do so using your Cloupor M4 Tool. USE CAUTION and be extremely careful not to damage the atomizer coil.

Within the crucible of your Cloupor M4 tank, the coil works to clean itself by burning off any residue that comes in contact with it. We don’t recommend using any type of liquid cleaning agent in the Cloupor M4 tank, as doing so could cause it to malfunction.

The glass globe and draw stem can be soaked in isopropyl alcohol until the buildup dissolves. Do not clean the rubber or silicone o-rings with alcohol, as it could damage the rubber. Use warm soap and water to soak until clean. Agitate occasionally while soaking for stubborn buildup.

A: Within the globe of your Cloupor M4 Tank, the coil works to clean itself by burning off any residue that comes in contact with it. We don’t recommend using any type of liquid cleaning agent in the Cloupor M4 coil, as doing so could cause it to malfunction. If you need to remove concentrate from the tank, you can do so using your Cloupor M4 Tool, but we suggest avoiding putting any metal near the atomizer.

The glass globe and draw stem, however, will take on a substantial amount of buildup. Monitor and clean as needed. Check your vape each time you use it.

A: On certain parts alcohol is fine. The top cap will incur the most buildup, soaking it in alcohol or cleaning with alcohol soaked cotton swab are effective cleaning methods.

Cleaning the atomizer is not recommended, replace as needed.

Make sure you don’t expose the atomizer or battery to any liquids whatsoever. If you need to clean the outside of the Cloupor M4, use a warm damp cloth. If the Cloupor M4 gets wet in any way, allow to dry in the sun or a warm dry area until COMPLETELY DRY. Attempting to use the Cloupor M4 if wet will cause serious damage to the unit.

A: The glass globe and draw stem will incur the most buildup, soaking them in alcohol or cleaning with alcohol soaked cotton swab are effective cleaning methods. Make sure you don’t expose the atomizer or battery to any liquids whatsoever.
A: The atomizer should be replaced as needed on the Cloupor M4. When you notice a distinct change in aroma, it’s time to replace.

Ordering – Returns – Warranty

A: 1 Year
A: Not at this time.
A: Shenzen Cloupor Technology. is handling all of the warranty requests and service for the Cloupor M4. Full warranty and contact information for Shenzen Cloupor Technology is available on the warranty tab.
A: Contact Shenzen Cloupor Technology for more information about warranty registration. If you need proof of purchase information for your VapeWorld purchased Cloupor M4, please contact us!

If you have any other questions about the Cloupor M4 vaporizer, please contact us!

Product Dimensions 6.38in x .75in x .75in (16.2cm x 1.9cm x 1.9cm)
Package Dimensions 7in x 3in x 2in (17.8cm x 7.6cm x 5.08cm)
Product Weight .2lbs (.09kg)
Package Weight .75lbs (.34kg)
Vapor Path Ceramic, steel
Tank Material Ceramic, Steel, Glass
Tank Capacity ~One Session
Charging Options USB/110v/220v
Battery Capacity 650mAh
Resistance 2.5Ohm
Voltage 3.5v
Auto-Off? Yes, 10 second.
Safety Power Switch Yes, 5-Click
Heating Element Nickel/Aluminum-Alloy coil
Warm-Up Time ~3 Seconds
Country of Manufacture China
Warranty 1 Year

Included with Purchase:

  • ClouTank M4 Kit Vaporizer
  • 650mAh F1 Li-Ion Battery
  • USB Cable
  • AC USB Adapter
  • Cleaning Brush
  • Big Mesh Screen
  • Small Mesh Screen
  • Air Flow Ring
  • User Guide

Cloupor M4 User Guides

*Adobe Reader or PDF viewer Required

Getting the Most Out of Your Cloupor M4

  • Drawing after the heater has cooled down will allow the air vents to stay free of blockage.
  • Never leave a Cloupor M4 in a hot car. Ever.
  • Try and keep the Cloupor M4 vertical when in use, and directly after, as melted concentrate can leak out of the crucible if you lay the pen on its side while warm.
  • Allowing the Cloupor M4 to freeze can damage the atomizer. Avoid temperatures below 40 degrees.
  • Use caution with the included tool, as it could damage the atomizer coil if you aren’t careful.
  • Overloading more than one session’s worth of concentrate is a potential recipe for mess.

Cloupor M4 Maintenance

Cleaning the Cloupor M4 couldn’t be easier. If the atomizer coil has gotten too much buildup, replace it with a new one.

The inside of the draw stem and glass globe will take on the most buildup, remove the o-rings and clean with soap and water, and soak the glass and draw stem in isopropyl alcohol and clean with a cotton swab.

If any concentrate has made it onto the body of the Cloupor M4, wipe off with a warm damp cloth.

Need Assistance with your Cloupor M4?

Try these Solutions to common issues:

A: A few things could be causing this. Is the 5-click safety lock in place? Try clicking your Cloupor M4 button five times and see if anything happens.

Are you getting any light at all from the button? If not, make sure that its charged properly. This seems obvious, until you realize the power strip you were plugged into wasn’t turned on. Or…the USB port you were plugged into wasn’t actually a powered USB port. Or…there are many reasons to think your vaporizer is charging…when it isn’t. It happens all the time.

If you have charged it fully, and unlocked the power button, and are still getting no vapors, remove the draw stem, press the button, and see if the atomizer is at least getting warm?

If you have no activity from a fully charged Cloupor M4, its possible that your atomizer has died. We have replacement cartridges available if needed.

A: Make sure your Cloupor M4 is fully charged, and the atomizer coil is fully seated and loaded properly(not overloaded).
A: The Cloupor M4 was designed for liquids and concentrates only, so loading aromatic blends will result in undesired results. Do not load aromatic blends in coils designed for liquids.
A: This is a natural situation with the Cloupor M4. There are fresh air intake holes on the sides of the Cloupor M4 atomizer cartridge. They are connected to small holes in the bottom of the crucible. When your solid concentrate melts, it may fill the holes located in the bottom of the crucible. When this liquid cools, it blocks the holes, so drawing is difficult.

This is easily remedied by heating up the Cloupor M4 for a short time, blocking one of the two holes on the side of the cartridge (they are in the silver band) and drawing. If warm enough, this should clear on one side, then repeat on the other side.

As you continue to use the Cloupor M4, be mindful of this blockage potential. One trick to prevent it from happening is to continue to draw through through the Cloupor M4 once a minute as it is cooling. Once all the internals have cooled to room temperature, you can stop.

If these troubleshooting tips don’t work, please contact us.

Cloupor VaporizersVape World carries atomizers and cartomizers that are compatible with the threading on the Cloupor M4. Cloupor M4 Atomizer

Cloupor M4 1 Year Warranty

Shenzen Cloupor Technology warrants their products to be free from defects in materials and workmanship for one (1) year from the date of purchase under proper use. Warranty excludes cartridges, misuse or abuse, and any accidental damages.

*IMPORTANT: WARRANTIES NON-TRANSFERABLE. ITEMS PURCHASED ONLINE FROM E-BAY, AMAZON, CRAIGSLIST, ETC. ARE CONSIDERED 2ND HAND AND WARRANTIES NULL AND VOID!

If you need more information about Cloupor M4’s Warranty, please contact us

Leave a Reply